====== DHCP Authorization Setup ======
{{indexmenu_n>8}}

  - [[dpi:bras_bng:general_setup#fastdpi_l2_bras_setup| BRAS activation]]
  - [[dpi:bras_bng:bras_l2_vlan:bras_l2_vlan_session|What is a subscriber session]]
  - [[dpi:bras_bng:bras_l2_vlan:bras_l2_vlan_dhcp| DHCP handling]]
  - [[dpi:bras_bng:bras_l2_vlan:bras_l2_vlan_arp_proxy|ARP proxy]]
     -   [[dpi:bras_bng:bras_l2_vlan:bras_l2_vlan_arp_proxy:bras_l2_vlan_arp_inspect|ARP inspection]]
     -     [[dpi:bras_bng:bras_l2_vlan:bras_l2_vlan_arp_proxy:bras_l2_vlan_arp_auth|ARP-request authorization]]
  - [[dpi:bras_bng:bras_l2_options:bras_l2_vlan_ipsg|IP source guard]]
  - [[dpi:bras_bng:bras_l2_options:bras_l2_vlan_local|Local traffic interconnection]]
  - [[dpi:bras_bng:bras_l2_vlan_term|Traffic termination]]
     -      [[dpi:bras_bng:bras_l2_vlan_term:bras_l2_vlan_term_as|Autonomous system level termination]]    
     - [[dpi:bras_bng:bras_l2_vlan_term:bras_l2_vlan_term_dna|Setting of termination parameters for each output interface]]
  -   [[dpi:bras_bng:cli:bras_l2_vlan_ctl|Manual subscriber properties changing]]
  -    [[dpi:bras_bng:cli:bras_l2_vlan_trace|Stingaray Service Gateway BRAS tracing]]

<note tip>L2 DHCP Mode Overview: {{youtube>dnVsa7o8onQ?}}</note>

BRAS L2 for VLAN/QinQ-networks provides the following features:
    * //DHCP//: monitoring of the DHCP requests from clients; if the DHCP server reply is successfull, clients will be immediately authenticated via the Radius-protocol
  * //ARP proxy// – LAN ARP requests monitoring, blocking ARP requests from the WAN
  * //IP source guard// – verification that the LAN packet belongs to the same VLAN from which the DHCP registration was. If this condition is violated, the packet is dropped.
  * //Local traffic interconnection// (Intra-network traffic exchange between subscribers)
  * //Traffic termination// from LAN to WAN, //origination (grounding)// of the responding traffic from WAN to LAN

To perform these functions, fastDPI BRAS needs to know when a client session starts and when it ends, and also operate not only with the IP addresses of users, but also with their MAC addresses and tags of VLAN/QinQ networks.
With the help of this knowledge, it is possible to filter out inappropriate requests, thereby increasing security of the local network as a whole.

FastDPI BRAS L2 is suitable for both VLANs and QinQ (double VLAN, VLAN-per-user) networks. The QinQ network is more preferable, since it allows you to uniquely identify the user in a way independent of the user's hardware, but also for a regular VLAN network (with one VLAN packet header), where the VLAN number actually identifies not a user, but a group of users, for example, a house entrance or an entire apartment building, fastDPI BRAS allows you to implement some protection.

<note>BRAS L2 functions are relevant only when fastDPI is used in bridge mode.</note>

BRAS operates primarily on the L2 level, which means that if a packet from LAN is dropped or a decision to send it back to the LAN is taken, the packet payload wouldn't be recognized.

<note important>When implementing L2 BRAS (especially using the test bed with few test subscribers) it should be taken into account that due to architectural features and optimization for a large volume of processed traffic, BRAS may handle the subscriber base consisting of 1-2 subscribers incorrectly, that causes the appreciable delays in responses to DHCP/PPPoE packets. For a full-fledged work of L2 BRAS, it is required to load the Stingray Service Gateway with some kind of traffic in order to prevent the idle functioning of worker threads.</note>